Forum switched to read-only as of 2020/06/01
| Latest product reviews |
|---|
 |
 |
Smartphones  |
TV Connect  |
 |
Log In
HomeClockworkMod (CWM) Recovery easy install for RK3066 and RK3188 -- TWRP/CWM Flash-Tool and root for RK3288
Please donate to support OMA and CrewRKTablets firmware work, thank you !
Moderator
Firmware Guru
2012/10/06
Offline
Gents,
Just playing around with a dump of the stock firmware V01.00.09 😉
Thanks to Dan EE for providing the dump!
Oma Flex Elite LP 5.0.2 build v1.0
– stock recovery 5.0.0
– CrewRKTablets recovery TWRP 2.8.4.0
– sekernel #137 preempt 17 Jun 2015
– latest su, su-binary, busybox
– Reboot Menue
– Soft Volume Buttons
hints:
– instructions are included in the download pack
– to enable development options tap 5 times on build number
– to improve UI feeling: disable all animation scales in developer options,
…use Nova launcher and set animation/scroll to “faster than light” and
…enable Entropy Fixer with value 256
– Oma's favourite apps for LP
Be aware: it is your own risk!
– Oma -
The following users say thank you to Oma7144 for this useful post:
graphdarnellPer aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/07/17
Offline
Oma,
I still have not had any luck flashing a partition even going straight the rommask. I enter the rommask by pushing the rest button through the pinhole while holding down the +volume button. I am running Windows 7 on the PC and launching the AntroidTool with admin rights.
Dan EE
2015/07/17
Offline
I can transfer files as a media device MPT
Moderator
Firmware Guru
2012/10/06
Offline
Most likely a driver issue. Use the included Driver Assistant. De-install driver first, then install again.
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/07/17
Offline
Done, No change. I have verified the rockusb.sys file in windows/system32/drivers matches the one included with the RKDriverInstaller.
2015/07/17
Offline
Oma,
I can read the eMMC ID, info and the sectors with the Linux upgrade_tool. Still no luck with the with the lower format or writing anything. It fails the TestDevice command. I think that the eMMC is locked and I don't have enough info to get by this.
Dan EE
2015/07/17
Offline
I have not been able to get to the maskrom no matter what combination of reset, volume up, volume down or power on combination I try. It always goes to loader mode. I think the loader may be a special version that won't let me write to the eMMC.
Moderator
Firmware Guru
2012/10/06
Offline
Dan EE said
I ran into a snag. It won't lower format the e-MMC. It just stays at 0%. It also reports "Device Test Start" and "Device Test Fail" If I try to flash a partition.
From the other thread ... is the tab still booting?
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/07/17
Offline
Yep, still boots. If I could brick it, it should go to the rom mask loader. It may need a signed update.zip to get a rom onto it. I could try to ground the recovery pin on p21 of the processor. This would take a bit of effort and would be impossible if there's no via to scrape and mag wire to.
Moderator
Firmware Guru
2012/10/06
Offline
Pls try:
adb reboot bootloader
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/07/17
Offline
Done that, same result. After looking at the firefly wiki, they actually ground the eMMC clock to force it into maskrom.
Moderator
Firmware Guru
2012/10/06
Offline
One step back. Pls check the usb driver: http://www.nirsoft.net/utils/usb_devices_view.html
Flash driver is: VID_2207&PID_320A
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/07/17
Offline
I can't get to the website now. The VID=2207,PID=320A in device manager and Linux when in bootloader. Matches .inf file for a 3288. I am at work now and I am pretty sure about the PID. It may be 310A? I tried using a bootable image of firefly 4.4. It hung which may be promising since it doesn't have the LCD driver. Maybe a bootable TWRP image?
Moderator
Firmware Guru
2012/10/06
Offline
Sorry, VID_2207&PID_320A is the correct one for RK3288.
I would like to know if the tab gives this ID in flash-loader modus (all cable plugged, Reset, then Power & Vol+) and if the ID gets lost while action in the flash tool.
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
Most Users Ever Online: 803
Currently Online:
122 Guest(s)
Currently Browsing this Page:
1 Guest(s)
Devices in use: Desktop (101), Phone (21)
Top Posters:
finless: 604
DarthJabba: 551
maikal: 394
mussonero1: 350
JEssicannn: 279
alex: 252
damo: 243
DanielVd: 237
Newest Members:
AnnaStockm
IAmTheOne86
tkowalski
Devlin
gitidi3813
goliad
Forum Stats:
Groups: 10
Forums: 185
Topics: 6129
Posts: 60941
Member Stats:
Guest Posters: 43
Members: 266802
Moderators: 5
Admins: 1
Administrators: admin
Moderators: globula_neagra, exelletor, JochenKauz, Oma7144, cracktech
CrewRKTablets moderators: JochenKauz and Astralix
