Forum switched to read-only as of 2020/06/01
| Latest product reviews |
|---|
 |
 |
Smartphones  |
TV Connect  |
 |
Register
Log In
HomeClockworkMod (CWM) Recovery easy install for RK3066 and RK3188 -- TWRP/CWM Flash-Tool and root for RK3288
Please donate to support OMA and CrewRKTablets firmware work, thank you !
2015/01/10
Offline
I ve had just installed V88 by Oma 3.2 GEN2 on my Alcor Zest Q813IS device (copy of Chuwi V88) and now its dead. Do you have any idea how can i fix it? Thank you very much!
Moderator
Firmware Guru
2012/10/06
Offline
Did you change the loader?
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/01/10
Offline
I followed the instructions:
3) change the loader (skip when the firmware has the same loader generation)
a) run RKDevelopTool.exe
b) button with the 3 points: load the loader (gen1 = v1.24, gen 2 = v2.16)
c) Erase ID Block
d) Erase All Blocks
e) Download
Here I choose the gen2 loader, then I did c-d-e steps. RKDevelopTool.exe wrote on the screen that it was succesful, but since then the tablet is dead. It doesnt want to turn on, connect to my pc, anything...:( I tried these methods to save it (http://www.slatedroid.com/topic/76825-chuwi-v88-bricked-fixed/).
Moderator
Firmware Guru
2012/10/06
Offline
Could be that the usb flash-driver are not installed properly. Any reaction in the Flashtool while shorting the NAND pins?
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/01/10
Offline
Unfortunately nothing. 
Moderator
Firmware Guru
2012/10/06
Offline
Which windows?
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/01/10
Offline
Windows 7 64bit.
Moderator
Firmware Guru
2012/10/06
Offline
Here is a driver assistant: http://crewrktablets.arctablet.com/?wpfb_dl=1187
Make sure the pack is in C:
Uninstall driver first, then Install.
- Oma
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/01/10
Offline
I tried it now, but the problem is the same. The tablet doesnt do anything, when i connect to my pc. There is no sound or any notification about the missing drivers.
Moderator
Firmware Guru
2012/10/06
Offline
In such cases it is the best to try with an other PC.
- Oma -
The following users say thank you to Oma7144 for this useful post:
unyiattilaPer aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/01/10
Offline
Still nothing. Anyway thank you for your support. I think i would try to validate the warranty.
2015/01/10
Offline
Thanks God I could fix it. The problem was that in every forum they say that first connect the tablet to the pc and then short the NAND modul out. It worked for me in a different order.
Part 1: Open v88 and short out NAND module
1. Unplug usb and power charger from v88.
2. Perform a "Deep Power Off" by pressing the Power button for at least 20 secs
3. Start up both RKBatchTool and RKAndroidTool using admin privileges
4. Open v88 casing
6. Connect v88 to PC using USB
7. Locate pins 8 & 9 on the #1 NAND module and short them out using a small pin, paperclip or small screwdriver. If shorting out pins 8 & 9 don't work, try shorting out pins 7 & 8 and while you short them connect usb cable to the tablet.
8. By shorting out the NAND module, you have put your tablet in "Mask ROM Mode." The RKAndroidTool should now indicate your tablet is recognized by showing the following message: "Found RKAndroid MaskRom Rock Usb"
Moderator
Firmware Guru
2012/10/06
Offline
Ok, with connection of the usb-cable the flash-diver has been installed properly.
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
2015/06/30
Offline
Hi Oma!
A had problem with my Chuwi v88 first gen, and I tried the exactly same thing as unyiattila above did. My tablet doesn't turn into Mask ROM Mode, but the tablet has rebooted in german language and asks for a password: "Passwort zum Entschlüsseln des Speichers eingeben". I don't know what password should I use, and now if my tablet boots, this is the only interaction I can make with it. I hope you can help me. By the way your Kit Kat ROM 4.4.4 (if I good remember) with gen1 loader was on it.
Moderator
Firmware Guru
2012/10/06
Offline
Something went wrong during flash process. Flash again, incl. eraseIDB.
- Oma -
Per aspera ad astra, we rock the Tablets !
If you like our firmwares, please consider making a donation to support our work.
Thank you!
Most Users Ever Online: 749
Currently Online:
105 Guest(s)
Currently Browsing this Page:
1 Guest(s)
Devices in use: Desktop (88), Phone (15), Tablet (2)
Top Posters:
finless: 604
DarthJabba: 551
maikal: 394
mussonero1: 350
alex: 252
damo: 243
DanielVd: 237
Mark06: 222
Newest Members:
rkg2303
sergey-tax
houseofcandy
duviauxi
benevento89
pablovs
Forum Stats:
Groups: 10
Forums: 185
Topics: 6037
Posts: 60500
Member Stats:
Guest Posters: 43
Members: 262194
Moderators: 5
Admins: 1
Administrators: admin
Moderators: globula_neagra, exelletor, JochenKauz, Oma7144, cracktech
CrewRKTablets moderators: JochenKauz and Astralix
