Thanks Arctablet (and Kasty.. is this a person ?) for this awesome firmware !!

That fw give a second life for our arnova 10G2.

No problem to flash, good reactivity, well look, just a few things less better : the timeboot a little too long (but i am comparing with finless rom 2.2pro), chrome & firefox crashes and above all we can't move apps to sd (but it seems that ics is in cause).

I test the method to switch internal to external sd but I failed, if someone have a tips

THX for the good job.

hello.

If you need to test the rom you can count on me.
I have two tablets and I can do the test in one of them.

Greetings and thanks for the hard work.

Freiserk.

dcm said
Hi guys,

Thanks for this great firmware, I've managed to install it with no problems.

I have however a small problem with the touchscreen. Before flashing this fw I had a stock ICS from Arnova(I can't in it on their site) and the touch was working very well. After flashing this version the clicks on the touchscreen are misaligned by about 30 pixels towards the Arnova 10G2 letters. I've tried calibrating it various times and the problem persisted. I've been looking into dmesg and found this on the touchscreen driver init. Is there anything I can do to try to fix it?

 

<6>[ 4.141177] ThumbEE CPU extension supported.
<4>[ 4.146337] nt11003_ts_probe
<4>[ 4.149230] Install touch driver..the tp is nt11003,not touchplus tp_flag=-1063130423
<4>[ 4.158333] nt11003_ts_probe3
<4>[ 4.161368] ------------[ cut here ]------------
<4>[ 4.166021] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x4c/0x110()
<4>[ 4.173857] autorequest GPIO-319
<4>[ 4.177135] [<c04cc098>] (unwind_backtrace+0x0/0xf0) from [<c04e9c94>] (warn_slowpath_common+0x4c/0x64)
<4>[ 4.186555] [<c04e9c94>] (warn_slowpath_common+0x4c/0x64) from [<c04e9d2c>] (warn_slowpath_fmt+0x2c/0x3c)
<4>[ 4.196146] [<c04e9d2c>] (warn_slowpath_fmt+0x2c/0x3c) from [<c063f9f8>] (gpio_ensure_requested+0x4c/0x110)
<4>[ 4.205912] [<c063f9f8>] (gpio_ensure_requested+0x4c/0x110) from [<c063fc58>] (gpio_pull_updown+0x8c/0x154)
<4>[ 4.215686] [<c063fc58>] (gpio_pull_updown+0x8c/0x154) from [<c04e0518>] (nt11003_init_platform_hw+0x10/0xfc)
<4>[ 4.225634] [<c04e0518>] (nt11003_init_platform_hw+0x10/0xfc) from [<c07127cc>] (nt11003_ts_probe+0x1b4/0x4e0)
<4>[ 4.235666] [<c07127cc>] (nt11003_ts_probe+0x1b4/0x4e0) from [<c071c81c>] (i2c_device_probe+0xa0/0xd4)
<4>[ 4.245004] [<c071c81c>] (i2c_device_probe+0xa0/0xd4) from [<c0671e10>] (driver_probe_device+0xa8/0x158)
<4>[ 4.254509] [<c0671e10>] (driver_probe_device+0xa8/0x158) from [<c0671f20>] (__driver_attach+0x60/0x84)
<4>[ 4.263926] [<c0671f20>] (__driver_attach+0x60/0x84) from [<c0671654>] (bus_for_each_dev+0x48/0x84)
<4>[ 4.272996] [<c0671654>] (bus_for_each_dev+0x48/0x84) from [<c0670e14>] (bus_add_driver+0x9c/0x220)
<4>[ 4.282067] [<c0670e14>] (bus_add_driver+0x9c/0x220) from [<c0672500>] (driver_register+0xa8/0x138)
<4>[ 4.291137] [<c0672500>] (driver_register+0xa8/0x138) from [<c071cba0>] (i2c_register_driver+0x40/0xac)
<4>[ 4.300554] [<c071cba0>] (i2c_register_driver+0x40/0xac) from [<c04c23c8>] (do_one_initcall+0x94/0x164)
<4>[ 4.309971] [<c04c23c8>] (do_one_initcall+0x94/0x164) from [<c0408394>] (kernel_init+0x74/0x118)
<4>[ 4.318787] [<c0408394>] (kernel_init+0x74/0x118) from [<c04c81d0>] (kernel_thread_exit+0x0/0x8)
<4>[ 4.327581] ---[ end trace c78c77c2b1e104a0 ]---
<6>[ 4.670716] input: nt1103-ts as /devices/virtual/input/input2
<4>[ 4.676690] nvctp_CheckIsBootloader

Is the source of this rom available? I could try to find a fix/workaround for the problem.

Will this work on Arnova 10B G2?